Webcam testMicrophone testWebcam and mic test
TestsWebcam testMicrophone testWebcam and mic testHeadphone testPre-stream checklist
SetupsSetup builderSetup guidesAudio routingCamera checker
SettingsBitrate calculatorUpload calculatorSettings by platformTwitchYouTube LiveKickFacebook LiveTikTok LIVE
GearAll gearComparisonsStream Deck selector
GuidesChoose your gearConnect and set upFix a problemAll guidesAll tools
AboutCorrections and contact

Search stays on this device. Esc to close.

As an Amazon Associate I earn from qualifying purchases. How this site earns · Amazon offers a free 30-day Prime trial, with free delivery on eligible items.

Shure MV7+

USB now, an XLR interface later.

RØDE NT-USB+

A USB condenser for a controlled recording space.

Before you choose

Shure MV7+

The catch: Use USB for the microphone’s DSP and headphone features. On XLR, plan processing and monitoring at the interface; those USB features do not follow the analog cable.

You need:

  • A microphone stand or boom arm

Check first:

  • For USB: a USB-C port on your computer

RØDE NT-USB+

The catch: Use the direct USB route and place the microphone close enough for a clear voice before treating room reflections with processing. Choose another microphone if an XLR mixer connection is required.

Check first:

  • A USB cable

Everything to check before you buy

Where they differ

SpecsShure MV7+RØDE NT-USB+
ConnectionUSB and XLRUSB
Shure MV7+ also has an XLR output for an audio interface; RØDE NT-USB+ connects over USB only.
CapsuleDynamicCondenser
Shure MV7+ is dynamic, which picks up less of the room; RØDE NT-USB+ is a condenser, which suits a quiet room.
Stand in the boxNoYes
RØDE NT-USB+ comes with a desk stand; Shure MV7+ needs a stand or boom arm.

Where they are the same

Pickup patterns
Cardioid
Best USB recording format
24-bit, 48 kHz
Processing on the microphone
Yes
Headphone socket
Yes

Not enough data to compare

We haven’t confirmed a figure for one or both models on: Preamp gain needed, XLR cable in the box, USB cable in the box. The site leaves these out rather than guess.

What else each needs

Shure MV7+

MV7+
For USB: a USB-C port on your computer
For XLR: an audio interface or mixer with an XLR microphone input
For XLR: an XLR cable
A microphone stand or boom arm
Wired headphones with a 3.5 mm plug
  • Check first: For USB: a USB-C port on your computer. The cable in the box has USB-C at both ends. If your computer only has USB-A ports, you need a USB-C to USB-A cable rated for the same speed.
  • Optional: For XLR: an audio interface or mixer with an XLR microphone input. A computer has no XLR input. The interface’s preamp raises the microphone’s signal and sends it to the computer over USB.
  • Optional: For XLR: an XLR cable. None comes in the box.
  • You need: A microphone stand or boom arm. No stand comes in the box; it mounts on a 5/8-inch thread.
  • Optional: Wired headphones with a 3.5 mm plug. Its headphone socket lets you hear yourself straight from the microphone, before the computer adds delay.

RØDE NT-USB+

NT-USB+
A USB cable
A boom arm, if you want it closer
Wired headphones with a 3.5 mm plug
  • Check first: A USB cable. Our record of the box lists no USB cable. Check the box before you plan the connection.
  • Optional: A boom arm, if you want it closer. A desk stand is in the box. An arm lets you bring the microphone nearer your mouth without it sitting in the camera shot.
  • Optional: Wired headphones with a 3.5 mm plug. Its headphone socket lets you hear yourself straight from the microphone, before the computer adds delay.

Next step

Put either model into the setup builder to check it against your computer and the rest of your gear, or see all 27 side by side in USB microphones for streaming compared. Test your microphone before you go live.

Full profiles: Shure MV7+ and RØDE NT-USB+.

Sources